RADIOCULT.SU - APRS Track Direct

My position About ☰

reset

WCSAR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WCSAR-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Dg1h*
1734899118	13.73 Volt	10 Pkt	10 Pkt
1734896416	13.73 Volt	0 Pkt	0 Pkt
1734891010	13.73 Volt	0 Pkt	0 Pkt
1734889209	13.73 Volt	10 Pkt	10 Pkt
1734888308	13.73 Volt	10 Pkt	10 Pkt
1734887407	13.73 Volt	10 Pkt	10 Pkt
1734886506	13.73 Volt	10 Pkt	10 Pkt
1734885605	13.73 Volt	10 Pkt	10 Pkt
1734884704	13.73 Volt	10 Pkt	10 Pkt
1734883804	13.73 Volt	10 Pkt	10 Pkt
1734882903	13.73 Volt	10 Pkt	10 Pkt
1734882002	13.73 Volt	10 Pkt	10 Pkt
1734881101	13.73 Volt	10 Pkt	10 Pkt
1734879299	13.73 Volt	10 Pkt	10 Pkt
1734878399	13.73 Volt	10 Pkt	10 Pkt
1734877498	13.73 Volt	10 Pkt	10 Pkt
1734876597	13.73 Volt	10 Pkt	10 Pkt
1734875696	13.73 Volt	10 Pkt	10 Pkt
1734874795	13.73 Volt	10 Pkt	10 Pkt
1734873894	13.73 Volt	10 Pkt	10 Pkt
1734872993	13.73 Volt	10 Pkt	10 Pkt
1734872092	13.73 Volt	10 Pkt	10 Pkt
1734868489	13.73 Volt	0 Pkt	0 Pkt
1734866687	13.73 Volt	0 Pkt	0 Pkt
1734865786	13.73 Volt	0 Pkt	0 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Temp: 0, 0.5, -64

I1: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)