RADIOCULT.SU - APRS Track Direct

My position About ☰

reset

ZL4AA-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ZL4AA-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Batt Volts*	Batt Amps*	PV Volts*	PV Watts*
1735006202	13.7 V	2.7 A	62.8 V	37 W
1735005602	13.7 V	2.6 A	61.4 V	37 W
1735005002	13.7 V	2.6 A	64.4 V	38 W
1735004402	13.7 V	2.7 A	61.8 V	39 W
1735003802	13.7 V	2.8 A	61.9 V	40 W
1735003202	13.7 V	2.9 A	61.1 V	41 W
1735002602	13.7 V	2.9 A	64.4 V	42 W
1735002002	13.7 V	3 A	63 V	43 W
1735001403	13.7 V	3.1 A	63.5 V	44 W
1735000802	13.7 V	3.3 A	64.7 V	47 W
1735000202	13.7 V	3.4 A	64 V	49 W
1734999602	13.7 V	3.6 A	63.8 V	51 W
1734999002	13.7 V	3.8 A	61.9 V	54 W
1734998402	13.7 V	3.9 A	62.2 V	56 W
1734997802	13.7 V	3.1 A	63.1 V	45 W
1734997202	14.3 V	6.3 A	60.4 V	93 W
1734996602	14.3 V	6.7 A	58.9 V	98 W
1734996002	14.3 V	7 A	54.5 V	104 W
1734995402	14.2 V	7.1 A	54.4 V	106 W
1734994802	14.3 V	8.1 A	59.8 V	118 W
1734994202	14 V	7.5 A	56.1 V	111 W
1734993602	14.1 V	9.6 A	52.3 V	139 W
1734993002	13.6 V	4.8 A	50.4 V	67 W
1734992403	13.7 V	7.1 A	52.7 V	101 W
1734991802	13.8 V	8.5 A	52.4 V	121 W

*Used Equation Coefficients:

Batt Volts: 0, 0.1, 0

Batt Amps: 0, 0.1, 0

PV Volts: 0, 0.1, 0

PV Watts: 0, 1, 0

Value5: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)