RADIOCULT.SU - APRS Track Direct

My position About ☰

reset

SQ9MTW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9MTW-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Sate*	Temp*	Pa*	Volt*
1734919431	10	26.3 C	970 hPa	6 V
1734917911	9	26.3 C	970 hPa	6 V
1734916395	9	26.3 C	970 hPa	6 V
1734913346	9	26.2 C	969 hPa	6 V
1734911820	9	26.2 C	969 hPa	6.6 V
1734910296	8	26.2 C	969 hPa	6 V
1734908770	9	26.3 C	969 hPa	6.3 V
1734907250	8	26.3 C	969 hPa	6.3 V
1734904202	8	26.2 C	968 hPa	6.6 V
1734902682	10	26.1 C	968 hPa	6.3 V
1734901156	9	26.1 C	968 hPa	6.3 V
1734899630	11	26 C	968 hPa	6 V
1734896584	10	26.2 C	968 hPa	6 V
1734895059	9	26.2 C	968 hPa	6 V
1734893526	8	26.2 C	968 hPa	6 V
1734892002	10	26.2 C	968 hPa	6.3 V
1734890470	10	26.2 C	968 hPa	6.3 V
1734888940	9	26.1 C	968 hPa	6 V
1734887415	10	26.1 C	968 hPa	6.3 V
1734885888	11	26.1 C	968 hPa	6.3 V
1734884363	9	26.1 C	968 hPa	6.3 V
1734882842	10	26.2 C	967 hPa	6.3 V
1734881310	10	26.3 C	968 hPa	6.3 V
1734879767	9	26.4 C	967 hPa	6.3 V
1734878243	9	26.3 C	967 hPa	6 V

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Pa: 0, 1, 0

Volt: 0, 0.1, 0

--: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)