RADIOCULT.SU - APRS Track Direct

My position About ☰

reset

XE2J-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE2J-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Eff1h*	Temp*
1730415956	8.63 Volt	100 Pcnt	28.5 C
1730415056	8.78 Volt	100 Pcnt	29.5 C
1730414156	9.08 Volt	100 Pcnt	29.5 C
1730413256	9.38 Volt	100 Pcnt	28.5 C
1730412356	9.75 Volt	100 Pcnt	27.5 C
1730411456	9.9 Volt	100 Pcnt	28 C
1730410556	10.05 Volt	100 Pcnt	27.5 C
1730409656	10.2 Volt	100 Pcnt	27 C
1730408757	10.2 Volt	100 Pcnt	28 C
1730407857	10.28 Volt	100 Pcnt	29 C
1730406957	10.28 Volt	100 Pcnt	29.5 C
1730406057	10.43 Volt	100 Pcnt	31 C
1730405157	10.5 Volt	100 Pcnt	32 C
1730404257	10.43 Volt	100 Pcnt	31.5 C
1730403357	10.35 Volt	100 Pcnt	31.5 C
1730402458	10.43 Volt	100 Pcnt	32.5 C
1730401557	10.13 Volt	100 Pcnt	34 C
1730400657	10.2 Volt	100 Pcnt	36 C
1730399757	10.35 Volt	100 Pcnt	38 C
1730398857	10.35 Volt	100 Pcnt	37.5 C
1730397957	10.5 Volt	100 Pcnt	36.5 C
1730397057	10.28 Volt	100 Pcnt	34 C
1730396157	10.35 Volt	100 Pcnt	33 C
1730395257	10.35 Volt	100 Pcnt	33 C
1730394357	10.28 Volt	100 Pcnt	32.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)