RADIOCULT.SU - APRS Track Direct

My position About ☰

reset

BV8SI-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV8SI-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1734980935	13.1 C	10 p	35 p	866 p
1734979734	13.9 C	12 p	36 p	866 p
1734978535	13.2 C	13 p	35 p	865 p
1734977335	14.4 C	11 p	33 p	865 p
1734976134	13.3 C	11 p	31 p	864 p
1734974935	14 C	11 p	27 p	863 p
1734973735	14 C	9 p	28 p	864 p
1734972534	13.8 C	7 p	28 p	864 p
1734970135	14.3 C	9 p	32 p	868 p
1734968934	13.7 C	10 p	33 p	868 p
1734967735	14.9 C	13 p	30 p	869 p
1734966535	14.9 C	10 p	29 p	867 p
1734965334	13.7 C	7 p	29 p	866 p
1734964135	15.1 C	12 p	33 p	870 p
1734962935	15 C	10 p	33 p	869 p
1734961734	14.7 C	11 p	33 p	869 p
1734960534	15.1 C	12 p	36 p	869 p
1734959335	14.8 C	10 p	36 p	867 p
1734958135	14.4 C	14 p	36 p	866 p
1734956934	15.1 C	12 p	33 p	865 p
1734955735	14.9 C	10 p	49 p	863 p
1734954534	13.9 C	11 p	93 p	863 p
1734953335	15 C	28 p	107 p	862 p
1734952135	15.1 C	54 p	97 p	846 p
1734950934	15.3 C	25 p	54 p	803 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)