RADIOCULT.SU - APRS Track Direct

My position About ☰

reset

IR3EO-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR3EO-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1734883218	138 Pkt	920 Pkt	12.01 Volt
1734882918	152 Pkt	930 Pkt	12.01 Volt
1734882618	136 Pkt	910 Pkt	12.01 Volt
1734882318	134 Pkt	910 Pkt	12.01 Volt
1734882018	135 Pkt	910 Pkt	12.01 Volt
1734881718	126 Pkt	900 Pkt	12.01 Volt
1734881418	154 Pkt	910 Pkt	12.01 Volt
1734881118	150 Pkt	900 Pkt	12.01 Volt
1734880818	121 Pkt	870 Pkt	12.01 Volt
1734880518	141 Pkt	910 Pkt	12.01 Volt
1734880218	151 Pkt	910 Pkt	12.01 Volt
1734879918	142 Pkt	890 Pkt	12.01 Volt
1734879618	135 Pkt	880 Pkt	12.01 Volt
1734879318	137 Pkt	870 Pkt	12.01 Volt
1734879018	131 Pkt	860 Pkt	12.01 Volt
1734878718	135 Pkt	850 Pkt	12.01 Volt
1734878418	132 Pkt	840 Pkt	12.01 Volt
1734878118	131 Pkt	840 Pkt	12.01 Volt
1734877818	131 Pkt	860 Pkt	12.01 Volt
1734877518	149 Pkt	870 Pkt	12.01 Volt
1734877219	145 Pkt	840 Pkt	12.01 Volt
1734876919	132 Pkt	850 Pkt	12.01 Volt
1734876619	128 Pkt	840 Pkt	12.01 Volt
1734876319	120 Pkt	850 Pkt	12.01 Volt
1734876019	111 Pkt	860 Pkt	12.01 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Volt: 0, 0.079, 0

DgR: 0, 0.001, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)